Rockin' and Rollin'

Roller tip rockers...that is all.



- Posted using BlogPress from my iPhone

I'm all geared up.

Well after two outings to the track with miserable 2.09 60' times I decided it was time for a change...a gear change. I took out the 3.73 and installed a 4.10. It's hard to say what this will do at the track because on the street it goes right to tire spin in first gear...even from a roll. So I think I should be able to pick up a few tenths...if I can get it to launch without spinning...stay tuned!





- Posted using BlogPress from my iPhone

Still slow...but consistently slow

I took the truck out to the track again to see if it would pick up some with the boost controller. It was on 11psi with the meth on. It ran dead nuts on what it did the first time. It went 8.62@83.10mph then went 8.64@83.23mph. It is fun as crap and the truck surprises a lot of people. They don't expect a turbo whistle out of a truck that looks like this! I had lots of people asking about it and commenting on it.



- Posted using BlogPress from my iPhone

Cruise-in

Rust stains, green algae growing on the tailgate, grass stuck to the wheels from weed whacking, Sid's writing in the chalk-like paint...I fit right in with the show-n-shine crowd at the local cruise-in! ;-) ...but lots surprised smiles when people look under the hood.



- Posted using BlogPress from my iPhone

Gauge-arrange

Moved the tach to the steering column and permanently mounted the meth light in the boost gauge bracket...cleaned up some wiring, hooked up the boost gauge back light.

Then pulled a plug and was surprised to find them black as night! Under boost I've leaned it out to about 11.7 - 12.0 and have been running the meth (I would assume the steam would clean them)...but still have black plugs...I cleaned the plugs reset the idle mixture I'll see if that helps...still runs strong - just a bit surprising as I thought it was pretty lean.

- Posted using BlogPress from my iPhone

Boost: it's controlled.

I took the truck for a drive this morning to test/set the boost controller...it works. I've set it at 11-ish lbs...seems pretty strong.



- Posted using BlogPress from my iPhone

Crap it's hot!

It's 105 degrees today so what better day to lower the under hood temp with some header wrap. Blue is a little crazy looking but it was free thanks to my friend Bryan. And you can also see the boost controller is in place.



- Posted using BlogPress from my iPhone

Boost Controller

In keeping with my homemade cheapo crap. I put together this boost controller for about $12. It's a pressure relief valve from Grainger with barb jammed in and JB Welded in place. The idea was stolen from a friend of mine who runs one on a 5 second blow-through Mustang...so, it works.



- Posted using BlogPress from my iPhone

Video of the pass...

Thanks to my friend John for getting the video on the trucks first pass...

8.66 @ 82.78mph!!

I drove the truck to Dunn-Benson dragstrip tonight...a 33 mile drive. Made a single pass...went 8.66 with a lazy 2.09 60'....so given that my goal was to go 8.30's...this was an awesome first pass! Then got back in it and drove it 33 miles back home. (ignore the 2.09 reaction time...I forgot to turn the data logger on and did it with the tree coming down - doh!)


- Posted using BlogPress from my iPhone

This seems a little shifty...

The shifts under power were a little "slushy"...so today I installed a B&M shift kit...now the 1-2 shift feels like you been hit in the ass with a baseball bat!


- Posted using BlogPress from my iPhone

I have to take a leak

Fixed several exhaust leaks (yes more) and switched to aluminum collector gaskets...and it picked up almost 3lbs of boost!

- Posted using BlogPress from my iPhone

Sunday drive.

On 275 M/T Drag Radials...boost works.


- Posted using BlogPress from my iPhone

I'm a street car!

Tagged, inspected, insured and on the streets...bitches!





...I've since fixed some exhaust leaks and picked up a ton of power...it makes a couple more pounds of boost on the spring so now puts down about 9 lbs....and sounds bad-ass whistles like crazy now. I threw the laptop in it the other day and the A/F is around 11.3 at WOT...I'm pulling 1.5 degrees per lb so I think it's still pretty safe and has more left in it. I also went back to a standard 6.5 power valve...with jetting at 69/78 and 35 squirters in both front and back. No bog but I think there is still power to be found out of boost...so more to come.



- Posted using BlogPress from my iPhone

What? I can't hear you...your all muffled.

Gonna try and get a tag...so I added a muffler.



- Posted using BlogPress from my iPhone

Did I mention...

That while installing the meth kit a box arrived from Summit with another larger set of squirters. I dropped a 42 in the secondary and was a bit much...a little boggy...so I left it in and changed to a white accelerator pump cam and bingo. It now hits pretty hard from a dead stop. Exhibit A:



- Posted using BlogPress from my iPhone

Wired

I got my adjustable Hobbs switch today. Got it wired up and mounted. But of course, I am missing the proverbial $.15 part...I didn't have the vacuum tee to plumb the boost to it but I did put some air to the switch and the whole system does work...so road test tomorrow.









- Posted using BlogPress from my iPhone

Doing some meth

Today I started installing my homemade water/meth injection system. The boost Hobbs switch had to be ordered so it's not fully functional but I got the pump, tank, injector,and relay installed so I was able to see it work.

- Posted using BlogPress from my iPhone

Finally getting there

After 2 years of jerking around I'm finally getting to a point of feeling good about this thing. I ordered some bigger squirters for the carb and after some accelerator pump cam changes got rid of the lean bog at the initial hit...it now goes straight to tire spin...which makes it go straight to boost...which makes it go to more tire spin...which makes it go to more boost...you get the idea.

I also installed a real throttle return spring setup instead of the kludged spring to coat hanger setup.

Now if I only had a way to get it to the track....

- Posted using BlogPress from my iPhone

7lbs of boost

A short clip of the truck making some boost..

- Posted using BlogPress from my iPhone